|
AnyReader: read from scratched CD/DVDs, unreliable LAN (Wi-Fi), damaged floppy/flash disks, etc.
Effectively copy corrupt data from any type of disks or faulty connections when standard copy methods
fail. AnyReader supports resumed downloads from a remote PC if the connection was broken during the
copy process (especially useful for unreliable Wi-Fi networks).
AnyReader is great for copying files from scratched CD/DVDs or defective floppy/hard disks. Normally,
when your computer is unable to copy files from a damaged disk it will abort and delete the part of the
file it has copied. AnyReader will continue copying the file right to the end; any data that hasn't been
recovered after several retries is replaced with blanks. This will allow you to effectively read every
byte of information that can be read.
Here are some situations where AnyReader can help: your CD/DVD drive can't read a bad, scratched or
trashed disks; the standard copying method fails because of an error, such as "(Bad CRC) A cyclic
redundancy check (CRC) checksum error occurred", "Cannot read from the source file or disk", an
unknown error or a bad disk; you have 2 bad copies of a file that you would like to put right; you can't
download a file across a wireless LAN because of a bad connection, etc.
AnyReader: http://www.objectrescue.com/download/anyreader/anyreader_setup.exe
AnyReader: http://www.objectrescue.com/pads/dp/distr/app-00ee11feaa7/site-001b1da2d96/lng-eng/anyreader_setup.exe |
|
The calculation is intended for the purposes of geometric and strength designs of spiral cylindrical torsion springs
made of wires and rods in circular sections, cold formed, loaded with a static or cyclic loading. Application is
developed in MS Excel, is multi-language and supports Imperial and Metric units and solves the following main
tasks:
- Automatic design of the spring.
- Selection of the optimal design of the spring with respect to strength, geometry and weight.
- Static and dynamic strength tests.
- Support for Cold formed springs and Hot formed springs
- Calculation of the working forces of a spring with known production and mounting dimensions.
- Calculation of mounting dimensions for known spring loading and production parameters.
- The application includes a table of commonly used spring materials according to ISO, ASTM/SAE, DIN, BS, JIS
and others.
- Support of 2D CAD (AutoCAD, AutoCAD LT, IntelliCAD, Ashlar Graphite, TurboCAD) and 3D CAD in full
calculation package (Autodesk Inventor, SolidWorks, SolidEdge, Pro/E).
The calculation is based on data, procedures and algorithms from specialized literature and the standards EN
13906-2, and DIN 2088.This module is a part of MITCalc - Mechanical and Technical Calculation Package for
gear, belt and chain drives, springs, beam, shaft, bolt connection, shaft connection, tolerances and many others.
MITCalc - Torsion Springs: http://www.mitcalc.com/download/MITCalcSprTors01.exe
MITCalc - V-Belts Calculation: http://www.mitcalc.com/download/MITCalcVBelts01.exe
The calculation is designed for a geometrical design and strength check of belt transmissions using V-belts.
Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the following
main tasks:
- Calculation for 2 or 3 pulleys.
- Automatic design of a transmission with the minimum of input requirements.
- Design and calculation of geometrical parameters (diameters of pulleys, axis distances, length of the belt, weight of
the transmission)
- Calculation of strength parameters (power transferred by the belt, number of belts, efficiency, etc.)
- Calculation of force conditions (prestressing, axis loading of the pulleys, etc.)
- Support of 2D CAD (AutoCAD, AutoCAD LT, IntelliCAD, Ashlar Graphite, TurboCAD) and 3D CAD in full
calculation package (Autodesk Inventor, SolidWorks, SolidEdge, Pro/E).
The application works with CAD systems and includes respective models of pulleys and belts. The calculations use
procedures, algorithms and data from basic documents and standards ANSI, RMA (Rubber Manufacturers
Association), ISO, DIN, BS, and basic documents from catalogues of companies CONTITECH (r) and Gates
Rubber Company (r).
Used standards: Narrow V-Belts ANSI/RMA IP-22; Traditional V-Belts ANSI/RMA IP-20; Light Duty V-Belts
ANSI/RMA IP-23; DIN 7753; DIN 2211; DIN 2215; ISO 4184 This module is a part of MITCalc - Mechanical and
Technical Calculation Package for gear, belt and chain drives, springs, beam, shaft, bolt connection, shaft
connection, tolerances and many others. |